Buttstocks

Buttstock assembly to mount to a Carbine AR

Fits all .223 and most .308 AR style rifles

Easy to Replace and quick to install

It adds up to 1-inch of height on the cheek rest, and an additional 1-1/16 inch length of pull

Made of super strong glass-filled nylon, weighs roughly half that of comparable stocks coming in at just 18 ounces.

Includes a Picatinny Rail on the bottom rear of the Stock Body to attach your choice of many accessories.

Designed a flat bottom index set screw (10-24) to eliminate that constant rattle of carbine collapsible buttstock. This also allows you to secure the stock in your favorite position.

3-axis adjustable butt plate assembly (keep in mind this butt plate assembly is interchangeable with the original MBA-1 Buttstock) will have the following movement:

Horizontal for linear adjustment (i.e. length of pull)

Vertical for a perfect butt plate fit into the curvature of the shoulder.

Lateral adjustment for a 1/2 inch left or right cast.

Adapts To Existing Commercial and Mil-Spec Buffer Tubes

Certain after Market Commercial Buffer Tubes that exceed 1.172? may not fit

The MBA-3 and MBA-4 will come in black.

Flat dark earth and Pink will be available in a few more months

Length of Pull (LOP) - Extended: 15 5/8?

Length of Pull (LOP) - Collapsed: 11 11/16?

Overall Length Extended: 8 3/4?

Overall Length Collapsed: 7 11/16?

Weight: 18.5 ounces

Items NOT included:

Sling Swivels,Carbine Buffer tube,Carbine Buffer Body Carbine Buffer Spring,or Latch Plate

Lock Ring Installation Notes:

When tightening the anti rattle set screw, be careful not to over tighten as it may cause the threaded insert to separate from the plastic stock body.

Interchangeable with Standard A1 or A2 Buttstocks

Length: 10-3/8" to 11.5" Extended

Fully Adjustable Cheek Rest adds up to 1 full Inch of Height

Weight: just 1.26 lbs

Fits all .223/5.56 and most .308 Rifles

Super Strong Glass Filled Nylon

Sling Swivel Not Included

Not interchangeable with Carbine with Telescoping Assemblies

Length: 10-3/8"

Weight: less than 3/4 lbs

Fits all .223/5.56 and most .308 Rifles

Super Strong Glass Filled Nylon

Easy to add Adjustable Cheek and Buttplate ( Sold Separately)

Sling Swivel Not Included

The STR carbine stock is a drop-in replacement for M4-type carbine stocks

The STR has improved cheek weld and two water resistant battery tubes on a reinforced polymer a-frame design

A shielded operation lever and a friction locking system prevent accidental adjustment and eliminate excessive stock movement

The STR incorporates two sling loops, left and right side QD sling mount locations and a replaceable butt pad

Two water resistant battery tubes that can be accessed by hand in any stock position

Storage tubes hold two CR123A or AA batteries per side

Compatible with Magpul ASAP and other receiver mount sling attachments

Reversible push-button QD sling mount

Replaceable butt-pad offers an anti-slip surface and increases impact protection

Commercial model mounts on commercial-spec sized receiver extension tube (not included) from manufacturers such as Bushmaster, DPMS, Olympic, and others

Stock Only Black in Color

Includes Magpul Buttpad!

Mounts on Commercial AR15/M16 Carbine Receiver Tube

Dark Earth in Color

The STR carbine stock is a drop-in replacement for M4-type carbine stocks

The STR has improved cheek weld and two water resistant battery tubes on a reinforced polymer a-frame design

A shielded operation lever and a friction locking system prevent accidental adjustment and eliminate excessive stock movement

The STR incorporates two sling loops, left and right side QD sling mount locations and a replaceable butt pad

Two water resistant battery tubes that can be accessed by hand in any stock position

Storage tubes hold two CR123A or AA batteries per side

Compatible with Magpul ASAP and other receiver mount sling attachments

Reversible push-button QD sling mount

Replaceable butt-pad offers an anti-slip surface and increases impact protection

Commercial model mounts on commercial-spec sized receiver extension tube (not included) from manufacturers such as Bushmaster, DPMS, Olympic, and others

Stock Only

Dark Earth Color

Includes Magpul Buttpad!

Mounts on Commercial AR15/M16 Carbine Receiver Tube

Black in Color

Commercial Buffer Tube required.

Stock Only

Made in U.S.A.

Black in color

Ambi One Point Sling End Plate, Castle Nut, 3 oz CAR Buffer, & Upgraded Chrome Spring

T6 Aluminum

Foam Tube Cover Also Included

US Made

Mounts on mil-spec rifle length receiver extension tube

Machined aluminum adjustment dials with positive click detent's

Corrosion resistant stainless steel shafts

Integrated bottom Picatinny rail for use with mono-pod

Reversible 1.25" loop front and rear sling mounts

Adjustable Check Piece and Butt Pad

Available in 223/556 or .308 Models

Black Only

Select Below

Four Integrated slots for sling attachment

Works with both 6-position standard and Mil-Spec Tubes

Ergonomic latch

Curved Saw-Tooth buttplate

Monte Carlo-Style Cheek rest

Reinforced Latch Pin

BLACK ONLY

COMES WITH BUFFER AND SPRING!

Entry Stock ARFX Listed below

ARFX Entry stock. This stock is only 7.25" long without recoil pad; yet is strong enough for its intended purpose "Close Quarters Battle." CQB usually involves heavy armor and the need for a stock that can be used to breech light doors or in hand to hand combat. Uses CAR length buffer and spring (not included). Special receiver extension tube, Sling swivel, foam overtube and choice of .5" recoil pad included.

Length 7.25". L.O.P.=10.45" (without recoil pad ) Weight: 265g ( 9.7 oz)

Select Stock Length

• (1) A2 Rifle Buttstock Extension Tube
• (1) Standard .223 Rifle Buttstock Buffer Spring
• (1) Standard Rifle Buffer Body Assembly

Kit includes:

• (1) .308 Buttstock Extension Tube
• (1) Standard .308 Buttstock Buffer Spring
• (1) Standard Buffer Body Assembly

Kit includes:

• Mil-Spec Carbine Tube
• .223 buffer spring
• .223 buffer body
• Latch Plate
• Lock Ring

Kit includes:

• Commercial Carbine Tube
• .223 buffer spring
• .223 buffer body
• Latch Plate
• Lock Ring

Interchangeable with Standard A1 or A2 Buttstocks

Length: 10-3/8" to 11.5" Extended

Fully Adjustable Cheek Rest adds up to 1 full Inch of Height

Weight: just 1.26 lbs

Fits all .223/5.56 and most .308 Rifles

Super Strong Glass Filled Nylon

Sling Swivel Not Included

Not interchangeable with Carbine with Telescoping Assemblies

Dark Earth

Kit includes:

• Mil-Spec Carbine Tube
• .308 buffer spring
• .308 buffer body
• Latch Plate
• Lock Ring

Kit includes:

• Mil-Spec Carbine Tube
• .308 buffer spring
• .308 buffer body
• Latch Plate
• Lock Ring

This package includes:

• (1) MBA-1 Modular Buttstock Assembly
• (1) A2 Buttstock Extension Tube
• (1) Standard .223 Buttstock Buffer Spring
• (1) Standard Buffer Body Assembly

The MBA-1

• Fully adjustable: extra 1″ height on cheek rest, additional 1 1/16″ length of pull with extended length buttplate
• Approximately half the weight of competitors’ adjustable stocks The “MBA” weighs just 1.26 lbs.
• Easy to replace and quick to install
• Fits all .223 and most .308 AR style rifles
• Super Strong Glass Filled Nylon

Features

• Modular buttstock assembly for the AR
• Interchangeable with standard A1 or A2 buttstocks or any aftermarket buttstock with overall length of approximately 10.5″
• Length: 10 3/8″ ( 11.5″ extended )
• Sling swivels not included
• Not interchangeable with carbine rifles with telescoping assemblies.
• Fully Ambidextrous and can be comfortably used shooting off either shoulder (Cheek piece pre-installed for right handed shooters but can be installed on either side for right or left hand shooters)

Our Buffer Tube Assembly Kit contains:

(1) A2 Buttstock Extension Tube

(1) Standard .223 Buttstock Buffer Spring

(1) Standard Buffer Body Assembly

Installing A2 buffer system on a carbine may affect function.

This package includes:

• (1) MBA-1 Modular Buttstock Assembly
• (1) .308 Buttstock Extension Tube
• (1) Standard .308 Buttstock Buffer Spring
• (1) Standard Buffer Body Assembly

The MBA-1

• Fully adjustable: extra 1″ height on cheek rest, additional 1 1/16″ length of pull with extended length buttplate
• Approximately half the weight of competitors’ adjustable stocks The “MBA” weighs just 1.26 lbs.
• Easy to replace and quick to install
• Fits all .223 and most .308 AR style rifles
• Super Strong Glass Filled Nylon

Features

• Modular buttstock assembly for the AR
• Interchangeable with standard A1 or A2 buttstocks or any aftermarket buttstock with overall length of approximately 10.5″
• Length: 10 3/8″ ( 11.5″ extended )
• Sling swivels not included
• Not interchangeable with carbine rifles with telescoping assemblies.
• Fully Ambidextrous and can be comfortably used shooting off either shoulder (Cheek piece pre-installed for right handed shooters but can be installed on either side for right or left hand shooters)

Our Buffer Tube Assembly Kit contains:

(1) .308 Buttstock Extension Tube

(1) Standard .308 Buttstock Buffer Spring

(1) Standard Buffer Body Assembly

Installing .308 buffer system on a carbine may affect function.