|
|
|
Multi Wrench
Multi Tool for Installing and Removal of the following items:
Free float Tubes, Barrel Nut, Extension Tube, Carbine Stock Spanner Nut, Compensator, and Buttstock Screw.
4140 Steel, Phosphated Finish and Hole on the end for hanging on the wall.
|
|
|
|
|
|
|
LR-308/AR-10 Free Float Tube Wrench
Used to install most free float tubes to upper in .308.
Will not work with Standard Handguards
|
|
|
|
|
|
|
Car Stock Nut Wrench
Car Stock Nut Wrench by DPMS.
Will not function with Colt Castle Nut
This tool will not break the second time used like others
|
|
|
|
|
|
|
The Flipper
Made of Delrin, this is the Tool for not mark up your receiver.
Clamp the Flipper into your vise and it holds any AR-15/M16, AR10 Lower receiver for assembly purposes. When finished, simply loosen the vise, flip "The Flipper" over and it will hold or retain any AR15/M16, AR-10 Upper receiver for assembly purposes.
Available in .223/5.56 or .308
Select Caliber Below
|
|
|
|
|
|
|
Panther Receiver Claw
The Claw is the perfect armorer tool for holding the AR15/16, AR-10 style upper receivers. Made of solid high strength Polymer.
With it tool the entire upper receiver can be assembled without taking a chance of putting any marks on your receiver. The upper is held in place by 2 pins (supplied) that go through both the front and rear assembly pin holes.
Available in either .223/5.56 or .308
Select Below
|
|
|
|
|
|
|
Combination Wrench
For removing the barrel nut, extension tube, and flash suppressor.
|
|
|
|
|
|
|
DPMS Aluminum Vise Jaws
Designed specifically for the 3/4" Heavy Barrels and 1" Bull Barrels. Vise jaws are notched with a "V" block for other assembly work.
|
|
|
|
|
|
|
Barrel Extension Wrench
Barrel extension wrench is designed to assist the removal and installation of the barrel extension. Also prevents misalignment with the outer guide.
.223/5.56x45 Only
|
|
|
|
|
|
|
Action Block by Brownell's
Replaces barrel vice and totally secures and protects receiver during removal and replacement of barrel assembly. Totally eliminates any possibility of damage to barrel detent pin or receiver detent notch. Fits all model Mil. Spec. receivers and is made of high pressure structural vinyl foam. Torque tested to over 200 ft. lbs.! Patent Pending.
|
|
|
|
|
|
|
AR15/M16 Handguard Removal Tool
This tool simply inserts into the magazine housing on the lower receiver, giving you the leverage needed to compress the delta ring assembly. This compression allows the Handguards to be easily removed as well as giving you easy access to the gas tube. Works with the A-15/EM-16, AP4 or Car-15 rifle.
Rifle must have the standard 2-piece Handguard.
|
|
|
|
|
|
|
Foster Head Space Gauges
The HEAD SPACE GAUGE is designed to protect your firearms from unnecessary damage and you, the shooter, from possible injury by showing whether or not the "head space" of an action is within tolerance. Essentially, head space is the distance between the face of the breech and the base of the cartridge when the action is closed. Accuracy and safety is threatened when there is excessive head space.
Forster Head Space Gauges are made with painstaking care to insure you accurate testing of the chamber. Each caliber Gauge comes in "GO", "NO GO", and "FIELD". If an action will not accept a "GO" Gauge, it will not accept cartridge cases of maximum length. If it accepts a "NO GO" Gauge the action may have excessive head space. If the action accepts a "FIELD" Gauge, it should not be fired. Every firearms owner should have Forster Head Space Gauges for safety and accuracy.
Specify "GO", "NO GO" or "FIELD" length gauge when ordering.
|
|
|
|
|
|
|
Delrin Punch
Hard plastic tapered punch that can be used to drive out the front and rear pivot pins.
Will not scratch or mar your pins or receiver.
|
|
|
|
|
|
|
Bore Brush
Bore Brush for either .223 or .308.
Select Below
|
|
|
|
|
|
|
Chamber Brush
Chamber Brush cleans both the barrel chamber and the inside of the barrel extension.
Select Either .223 or .308 below.
|
|
|
|
|
|
|
Mag Well Cleaning Brush
Quick and easy cleaning of your mags, works for AK and other mags. Dirt and damage to magazines are the main reason for weapon failure. Keep them clean for longer life.
|
|
|
|
