|
|
|
Tactical Multi-Mount system
Fits both Scopes and Electronic Dot sights
Easy On and Off with Repeat Zero
30mm Ring Supplied ( Optiional 1" Insert) Available Soon
Mil-spec Finish
Fits Picatinny or Weaver Rails (Both Bars are Included)
Tension Adjustable Knob for Rail Width
Can be used on Handguns or Long Guns
|
|
|
|
|
|
|
Tactical Bolt Catch
This new Bolt Catch has a larger bolt release pad that is much easier to locate and activate. The second benefit is the lower extended pad, which is used to hold the bolt carrier back when the magazine is not installed. This feature is excellent for tactical training when the magazine must be removed. Easy to install by removing the exterior roll pin and installing the new roll pin, which is included.
|
|
|
|
|
|
|
Oversized Safety Selector Switch
Oversized, extended selector for easier manipulation.
|
|
|
|
|
|
|
Miculek Comp
Jerry Miculek designed compensator. Standard .223 threaded muzzle end. Includeds jam nut for indexing comp for right and left handed shooters.
|
|
|
|
|
|
|
DPMS Flip Up Rear Sight
Flip Up Rear Sight Attaches to A3 Flat Top
|
|
|
|
|
|
|
DPMS Flip Up Front Sight
Flip Up Front Sight with 2 Height Settings. Clamps onto Rail Type Gas Block.
|
|
|
|
|
|
|
DPMS Front & Rear Pop Up Sight Set
Includes: Front and Rear Pop Up Sights.
|
|
|
|
|
|
|
Triple High Rail Detachable Rear Sight
Attaches to Standard A3 Flat Top. A2 Rear Sight Included.
|
|
|
|
|
|
|
Triple Low Rail Detachable Rear Sight
A2 Rear Sight Included. Attaches to A3 Flat Top.
|
|
|
|
|
|
|
Detachable Rear Sight
Attaches to A3 Flat Top
|
|
|
|
|
|
|
Detachable Carry Handle
Attaches to A3 Flat Top
|
|
|
|
|
|
|
Tactical Latch
Replaces the Charging Handle Latch. Easy Function for Tactical or Scoped Flat Top Rifles. Charge Handle Not Included. Latch Only.
|
|
|
|
|
|
|
Ambidextrous Safety Selector Switch
Three Piece Design. (With Screw) Replaces the Standard Selector for Safe and Fire from Either Side of the Receiver. Will not fit M16.
|
|
|
|
|
|
|
Detachable Front Sight
Detachable Front Sight ( Steel )
Includeds: Post, Detent, and Spring
|
|
|
|
|
|
|
Bull Barrel Gas Block
Gas Block for (.936 Dia.) Bull Barrel ( Steel ) Attaches with one set screw (provided)
Pre Ban with Banonet Lug
|
|
|
|
|
|
|
Single Rail Gas Block
Single Rail Picatinny Rail on top of Gas Block. (.750 Diameter)or (.936 Diameter) Select Barrel Size Below
|
|
|
|
|
|
|
4 Rail Gas Block
New Aircraft Aluminum Gas Block with 4 Picatinny rails. Now you can mount detachable front sights, lasers, flashlights, etc all at the same time. Currently made for the DPMS Bull Barrels. Comes ready to install.
Bore diameter is .936 or .750 Anodized Black.
Select size below
|
|
|
|
|
|
|
A1 Front Sight Tool
A1 Front & Rear Sight Adjusting Tool, Steel, 5 prong. A1 Sight Tool.
|
|
|
|
|
|
|
A2 Sight Tool
A2 Front Sight Adjusting Tool, 4 prong, Steel. A2 Sight Tool.
|
|
|
|
|
|
|
A-1/A-2 Combination Tool
A1/A2 Combination Front Sight Post tool
|
|
|
|
|
|
|
DCM NM Front Sight Post
National Match/DCM A1 Front Sight Post
This front sight post has a thinner front blade. Round. Approx. .050 diameter.
|
|
|
|
|
|
|
NM / DCM Square
National Match DCM Front Sight Post
4 sided square post .050 wide. Interchangeable with standard AR sights. Steel & phosphated.
|
|
|
|
|
|
|
Extended Front Post
Extended Front Sight Post - Square
Extended length post for detachable carry handle & detachable rear sight assembly. Approximately .030 longer than the standard A2 front sight post (.070 wide). 4 sides, square.
|
|
|
|
|
|
|
Hooded Aperture Sight
.040 Peep Diameter Hole
|
|
|
|
|
|
|
DPMS NM Rear Sights 1/4 min. Windage 1/2 min. Elevation Choice of Aperture Size
|
|
|
|
